Flooring Contractor in Wilmer, TX - Coated Concrete Floors Prepared to Hold
Slabline DeSoto Epoxy Flooring is a flooring contractor based in DeSoto that coats, polishes, seals and resurfaces concrete floors in Wilmer, TX, from home garages and pool decks to shop and warehouse floors.
Wilmer jobs, from garages to warehouse floors
Wilmer sits in southeastern Dallas County where I-45 crosses Cottonwood Creek, a short drive from where we're based in DeSoto. The calls we get here sound a lot like the ones from Hutchins and Lancaster. Homeowners ask about a garage, a patio or a pool deck, and local businesses ask about a shop or warehouse floor that has started to wear through in the places people walk and drive most.
The price here mostly follows the size of the floor, how much grinding and crack repair the concrete needs and the finish you choose, and the schedule turns on that same prep and on any permit the job needs. Under all of it is the slab, and I'd rather repair the concrete first than coat something that won't hold.
Concrete conditions we see on Wilmer properties
The floors we're called to in Wilmer tend to face the same few problems, and they're the things I look for first when I walk a slab here.
Dallas-Fort Worth averages about 20 days over 100 degrees and 29 freezes a season, and that swing works on concrete and whatever covers it.
Garage floors take hot tires, dropped tools and oil drips, and oil soaked into bare concrete keeps a coating from bonding until it's ground out.
Older slabs often carry old paint, sealer or a failed coating, and it has to come off before anything new will stick.
Shop and warehouse floors carry carts, forklifts and spills every day, and a thin coating over unprepared concrete wears through first in the busy lanes.
I check for each of these on your floor before I write the estimate, so the price covers what the slab actually needs.
Where we work in and around Wilmer
We're based in DeSoto and work in Wilmer and the cities around it, including Hutchins and Lancaster. If your city isn't listed below, please ask.
Floor and concrete services we offer in Wilmer
Epoxy Floor Coatings
For a garage, shop or utility room in Wilmer where bare concrete dusts and stains, we grind the slab, fix cracks and lay down a tough epoxy coat.
Commercial & Industrial Epoxy Floor Coatings
When a Wilmer shop or warehouse floor is wearing through in the traffic lanes, we prepare the concrete first and coat it to take carts, forklifts and spills.
Garage Floor Coatings
Oil drips, hot tires and road grit wear a garage slab down, so we grind out the stains and coat the floor so it wipes clean.
Polyaspartic Floor Coatings
Polyaspartic is a fast-curing coating that holds its color in sunlight, which suits a garage with the door open to a hot Wilmer afternoon.
Metallic Epoxy Flooring
For a game room, studio or showroom floor here, metallic epoxy gives a swirled, glossy look that hides the plain gray of the slab underneath.
Urethane Cement Flooring
Where a floor sees hot water, grease or heavy washdowns, like a commercial kitchen or food business in Wilmer, urethane cement holds up better than a standard coating.
Polished Concrete Flooring
If your slab is sound, we grind and polish the concrete itself to a glossy finish with no coating to peel, good for shops and open living areas.
Stained Concrete Flooring
Stain soaks into the concrete for warm, mottled color on a patio, porch or interior slab, then we seal it so it holds up to the sun.
Terrazzo Flooring
For a lobby or entry that takes heavy foot traffic, terrazzo sets marble or glass chips in a binder that we grind smooth and polish to a shine.
Basement Flooring
In a basement or below-grade room, we test the concrete for moisture before we choose a floor, because a damp slab will push a coating off.
Concrete Grinding & Surface Preparation
It's the part of the job you won't see once it's done. We grind off old sealer, oil and weak surface concrete so the new floor can bond.
Concrete Sealing
A clear sealer helps keep water, oil and stains out of a driveway, patio or garage slab and helps bare concrete hold up through Wilmer's heat and freezes.
Concrete Resurfacing & Overlays
When a patio, porch or interior slab is pitted or worn but still structurally sound, a thin overlay gives it a new, even surface without tearing it out.
Self-Leveling Concrete & Overlays
If a floor dips or slopes where a new coating or tile is going, self-leveling concrete flows out flat to give the next layer an even base.
Pool Deck Coatings & Resurfacing
A pool deck here bakes in the sun and stays wet, so we repair cracks and resurface it with a textured finish that grips underfoot.
Concrete Floor Stripping & Removal
When an old coating is peeling or a previous job failed, we strip it down to clean concrete, because a new floor over a failing one won't hold.
Get a written estimate for your Wilmer floor
Please send us a few details about your floor in Wilmer, and we'll reply within one business day to set a time to come out. I'll look at the concrete and measure it myself, and you'll get a free estimate in writing with no obligation.
- Call
- (972) 450-9481
- Hours
- Mon–Fri: 6 AM–10 PM, Sat–Sun: 7 AM–11 PM
Reasons to hire us for your Wilmer floor
I started this business in DeSoto in 2023 after learning the trade from my father, and the way we work still follows what he taught me about concrete.
I measure and run your job
I come out to look at your floor and measure it myself, and our own small crew does the work with me on site running it, so the person who quoted it is there.
Prep first, or no coating
My father taught me a floor is only as good as the concrete under it. If your slab won't hold a coating, I'll tell you so plainly rather than take the job.
Licensed, insured and guaranteed
We're licensed and insured, and our work is backed by our satisfaction guarantee. Your estimate comes in writing, so you know the scope before we start. Please call (972) 450-9481 to talk it over.
Questions about flooring work in Wilmer
Do I need a permit for floor or concrete work in Wilmer, TX?
It can, because Wilmer requires a permit before work starts to build, alter, repair or demolish any building or structure, and the city says that reaches nearly any construction-related project at a home or business. Work started before a permit is issued can draw a double fee and a citation. If we aren't sure about your job, we ask the city's Building Inspection Department before we quote, and when a permit is needed, we pull it ourselves.
How long does it take to get a building permit in Wilmer?
Wilmer asks you to allow two weeks for residential plan review and 30 days for non-residential, counted from when the application goes in. That's the city's review time, not the work itself, so when a job needs a permit, we apply early and set the start date after it's issued.
How do I schedule a building inspection in Wilmer, TX?
You request it on the city's automated inspection line at (972) 441-4472, which takes calls 24 hours a day. In most cases, an inspection requested by 4 p.m. happens the next business day, and a permitted job needs one or more inspections before the city counts it complete. When we've pulled the permit, we plan our work around those visits.
Does Wilmer require a business license to open a shop or warehouse?
No, Wilmer doesn't issue a business license and doesn't require one. A place of business does need a certificate of occupancy from the city's building inspections office at 972-441-6373, and a home-based business may need one as well. If you're fitting out a new shop floor, it's worth checking on yours before the work is scheduled.
What causes a garage floor coating to peel in Wilmer?
Peeling usually starts with what's under the coating, such as oil, old sealer or smooth concrete that was never ground, so the coating never really bonded. Moisture coming up through the slab can push it off too, and hot tires pull at a weak bond, which is why so many floors lift in the tire tracks first. We grind and check the slab before anything goes down.
How much does an epoxy garage floor cost in Wilmer, TX?
The cost depends mostly on the size of the floor and how much work the concrete needs before it's coated, so I give you a figure only after I've seen and measured it. Grinding off old sealer or a failed coating, filling cracks and evening out low spots all add to the price, and a polyaspartic or metallic system usually costs more than a basic epoxy coat. Your written estimate lists each of those, so you can see where the money goes.
Talk to us about your Wilmer floor
We take calls from early morning until late evening, weekends included, so please call (972) 450-9481 or send us the estimate form whenever it suits you.
Mon–Fri: 6 AM–10 PM, Sat–Sun: 7 AM–11 PM