Polyaspartic floor coatings in DeSoto TX - a coating that holds on a well-prepared slab
If your garage floor is stained, dusting or peeling, we grind the concrete by machine and put down a polyaspartic coating made to hold.
Is a polyaspartic coating right for my garage floor in DeSoto?
A polyaspartic floor coating in DeSoto is a hard, glossy coating we put down over machine-prepared concrete, usually a garage floor, so it resists stains and cleans up easily. Coating makers also describe it as standing up well to sunlight.
Most calls we get at Slabline DeSoto Epoxy Flooring start with a garage floor that's stained, dusty or wearing through an old coating, and we work in DeSoto and the cities around it. The price turns mostly on the floor's size, how much grinding the concrete needs and which coats go down. The schedule turns on how dry the slab tests, how long the product takes to cure and the weather on install day. If you'd like a more decorative look, metallic epoxy flooring is another option, and I'm glad to measure for either one.
How can you tell your concrete floor needs a coating?
Most homeowners call us once the bare concrete or an old coating starts showing its age. These are the signs I hear about most often, and what each one usually means for the slab underneath.
Your bare garage floor leaves gray dust on your shoes, which usually means the surface is wearing away.
Oil and tire marks have soaked in and won't scrub out, because bare concrete takes stains right in.
An old coating is peeling or lifting at the edges, which often points to poor preparation underneath.
Hot tires leave marks or pull up patches of an older coating right where you park.
Bubbles or blisters show up in a coating, which can mean moisture is pushing up through the slab.
The coating in a sunny garage has turned yellow or chalky, since some coatings don't hold up to sunlight.
If an old coating is lifting or blistering, please call us at (972) 450-9481 before you sand or patch it, so I can see what's causing it first.
What happens after you call us about a polyaspartic floor?
I come out to see the floor myself, and our own small crew does the work with me on site. Here is how a polyaspartic job usually runs from your first call to the finished floor.
Call us or send the form
Please call (972) 450-9481 or send the form, and we'll set a time for me to come out. We answer calls Monday through Friday from 6 AM to 10 PM and on weekends from 7 AM to 11 PM.
I come out and measure
I look over the floor, measure it and ask how the space gets used, and then you get a written estimate that names each step, including every coat and how we'll prepare the concrete. That way you can see what moves your price and compare it line by line with any other quote.
We settle on install days
We pick days that suit you and the city's rules, since DeSoto allows repair and alteration work in or next to residential areas from 7 am to 6 pm on weekdays and 8 am to 6 pm on Saturday. Sunday work runs 9 am to 5 pm without heavy equipment, so we usually plan grinding for a weekday or a Saturday.
Our crew prepares and coats
Our crew prepares the concrete by machine, puts the system down and cleans up, and I'm on site running the job. When it's done, I walk the finished floor with you, and the work is backed by our satisfaction guarantee.
Get a written polyaspartic estimate for your floor
Once you send the form, we reply within one business day to set a time for me to come out. Your estimate is free, done at your property and written down, with no obligation.
- Call
- (972) 450-9481
- Hours
- Mon–Fri: 6 AM–10 PM, Sat–Sun: 7 AM–11 PM
Polyaspartic systems, preparation and finish choices
A polyaspartic floor is usually built from more than one coat, so the name alone doesn't tell you much. A garage system often has a base coat, a broadcast of colored flake and a clear topcoat, and each of those choices changes the look and the price. Our estimate lists every coat that goes down, so you know exactly what you're getting.
We prepare the concrete by machine, grinding the top layer so the coating has a clean, open surface to grip, and we don't use acid for this. My father taught me that a floor is only as good as the concrete under it, so this is the part of the job I watch most closely. If a slab won't hold a coating, I'll tell you plainly rather than put one down.
Most of the rated soil across Dallas County is clay that swells and shrinks as it gets wet and dries out, so I look over the whole slab before I quote. In a garage that gets wet, we can add a grit to the coating for better footing. For a shop floor that sees heat, oils and hard cleaning, urethane cement flooring may suit it better.
Polyaspartic floor questions from DeSoto homeowners
How much does a polyaspartic garage floor coating cost in DeSoto?
Advertised pricing in the Dallas-Fort Worth area puts an installed residential floor coating at about $5 to $12 per square foot. Where your floor falls depends on its size, how much preparation the concrete needs and which coats go down. The written estimate I give you after measuring names each step, so you can see what sets your price.
Why does moisture in a concrete slab matter for a polyaspartic coating?
Moisture matters because a slab poured without a good barrier underneath to hold back ground moisture can push vapor up that blisters the coating and makes it fail. One coating maker requires the concrete to be dry and tested for moisture before its product goes on. That's why I check the slab first and tell you if it isn't a good fit.
How long does a polyaspartic floor take to cure before I can use it?
Polyaspartic is sold as a fast-curing coating, but how soon you can walk or park on it depends on the product used and the conditions that day. One maker says its coating goes on best between 60°F and 90°F with humidity at or below 85%, and that hotter weather shortens its working and drying time. We go by the product's own data, so you can plan the days without your garage.
Do I need a permit for a garage floor coating in DeSoto?
You might, because the City of DeSoto requires a permit when someone plans to build, alter, repair, move or demolish a building or structure. When a job needs a permit, we pull it ourselves and plan the work around the city's inspections. If I'm not sure, I check with the city's building office before I quote.
What should I look for in a polyaspartic floor coating quote?
A sound quote names every coat and how the concrete will be prepared, because a job sold as polyaspartic may put an epoxy base coat under a polyaspartic topcoat. One maker's guide calls for shotblasting or diamond grinding, both done by machine, and rules out acid etching, so look for one of those in the scope. The city also asks every contractor to register each year, and the city's Building Inspections Department answers questions about that. We're licensed and insured.
How do I clean a polyaspartic garage floor?
One maker says its polyaspartic cleans up easily with a neutral pH cleaner or a mild detergent, the kind that isn't acidic or harsh. If your floor has a textured, slip-resistant finish, that maker suggests scrubbing it by hand as part of routine cleaning.
Other floor systems worth comparing
Metallic Epoxy Flooring
If you want a floor with depth and movement to it, metallic epoxy gives a poured, swirled finish that suits a game room, showroom or finished garage.
Urethane Cement Flooring
If your floor takes hot water, steam cleaning or heavy wash-down, urethane cement is built for that kind of use and is worth weighing before choosing a topcoat.
Call to have your floor measured
Have your floor's size in square feet and a few install dates in mind when you call (972) 450-9481 or send the form, so we can plan around the weather and the city's work hours.
Mon–Fri: 6 AM–10 PM, Sat–Sun: 7 AM–11 PM